TRON Flynn, Quorra or Rinzler – LEG (A) Pieces Replica EL Panel Costume – Glow Tape + Driver

With this set you get:

1) Two pieces of replica shaped EL Tape for the boots of a Tron Costume - Sam Flynn or Quorra 

2) Two pieces of shaped and angled EL Tape to go round the knees

3) Two pieces of sacral shaped EL Panel to go at the lower back

4) Two pieces of 2cm X 25cm EL Tape 

4) A Powerful 8 XAA battery EL Driver -

5) A 2-way splitter, 3 x 3-way splitters and an extender 

6) 1.5metres of Velcro - with sticky hoop and sewable loop to make it easy to attach the set to a costume and have it removable

The Set is available in  can be any combination of these colours:

White or Aqua

The whole kit is ready to use - just plug and play!

Dimensions of the products:

If you are making a costume it is a good idea to plan it out properly.

For this set, the driver/inverter is very powerful and comes with a separate power pack

So here is the dimensions of all the parts plus lengths of wire between them.

 Feel free to message me if you have any questions

THE POWER PACK

Takes 8 X AA batteries (not supplied) and is 6.5cm X 6cm X 3cm

it has a 65cm thin power wire coming out of it that leads to the...

DRIVER

The driver is 6cm X 4cm X 4cm

It has the controls on it - Off, Flashing or On

It has a 55cm wire coming out of it that leads to the...

SPLITTER

The Splitter is 40cm long in total,

it is 20cm of wire which then splits into separate strands which are all 20cm long.

With a 3-way splitter attached to the driver

Two of these splits has another 3-way splitter for each of the parts on the leg

The third has a 2-way splitter attached that runs round the back to clip into the pair of EL Sacral pieces

A 1.2metre extender wire is also provided - this may not be needed but gives you more options of where the driver is kept on your body

The three pieces of EL Tape that run down the leg are:

1) TRON BOOT

This futuristic piece of footwear is designed to run down the ankle and wrap around the ankle and is a great finishing touch to any tron costume (these are also available in our store in white,  and orange)

2) KNEE JOINT

Running up from the boot piece, this piece of EL Tape takes an angle round the knee, exactly as in the original costumes

This has been made to largest size and will not fit everyone so it has been designed so you can just snip it down to the right size for you

That's right, it really is as easy as just cutting the unwanted part off either or both ends (sealing the cut with sellotape, glue or clear nail varnish is highly recommended)

3) 2cm x 25cm EL Tape

Another piece that can be cut to size is this straight piece of EL Tape that runs from the Knee Joint up to join the top half of the costume

Coming off the two way splitter at the back of the costume:

3) EL SACRAL

This pair of pieces sits at the base of the spine and i have to say looks pretty awesome

-

The tape is just 350 microns thick - that is 1/3rd of a millimeter!

Sticky back velcro is supplied that is the exact width of the EL Tape - be careful putting it on as that glue is VERY sticky

You must sew the other part of the velcro onto the costume making it very convenient to attach and remove

Of course you don't need to use the velcro, fix it any way you choose

Its not complicated or fiddly - ive just given all those details if you want to plan your costume before you buy the set - feel free to message me if you have any questions

The whole kit is ready to use - just plug and play!

OR CONTACT US IF YOU WANT ADVICE PLANNING YOUR SET

A wide selection of other EL Tape, EL Wire, Sequencers, Drivers and helpful EL accessories are available from this store

- - - - - - - - - - - -

This El Tape comes with a standard connector so simply plugs into any EL driver - this makes it easy to change between coloured wire on one driver

by using splitters you can also connect different strands to the same driver